Видео

top mistre miquanica👍👍👍

Great Video guys. I have just bought a 2024 MG3, so now I have an idea what the top end looks like. Thank you. Brisbane Australia

how many km till this needs doing

Bridged the connector got dash lights etc but still no crank. No power to starter signal wire. Any ideas? Thanks

Great video thank you for this. Can you send me please repair manual for this engine?❤

in all fairness huge well done on doing it. but because you re-used the old brake shoes that epb module was winding in ALOT.

Might sound dumb,But had friend Mobility car repaired after accident and the replacement front bumper Had No parking sensors...How the Work was cleared is beyond me.🙈🙉🙊

Good job on the clutch. Easier with the lift.❤😂

I knew a guy who was a builder used to drive his van with his left leg resting on the clutch pedal. He burnt out about four or five clutches in no time. But he knew what he was doing wrong.❤😂

Bloody hell that's handy when you're stuck in the middle of a field, or worse still a busy road🙈

Did your motor have 6 or 12 teeth? Because im very unsure on which bit i have to use to rewind the mechanisms in the calliper. Some people use torx and others use hex.

Great color same as my current 1992 looks a lot better than mine

They were fronts

I had to do this job on our mark 8 5 years ago after the bolts sheared off on the hub that hold the hafshaft so the halfshaft walked out of the diff. No need to take the bearing apart. and yes the bolts are stretch bolts The correct torque is 68 NM then 90 degrees. They sheared off because someone in the past tightened them to the wrong torque. Have the do the same job soon after 40,000 miles.

Nakubali

Thank you you have no idea how helpful you have been, have a great summer.😊

Chinese Sheite!

Very interesting and great to see content about this car. I have a 2019 mg3 which revs high and for a long period when starting from cold. The revs will not sit steady until the car is driven for 10 mins. Have you ever come across this?

i did it all correctly, but I don't know why the mirroring keep disconnecting after minutes. so I must start from the beginning again. do u have any suggestion?

Best review I have seen. Thank You

Almost as bad as a mk3 Golf!

We’ve had this happen 4 times in 10 months

Thanks ! A lot! very helpful! Where can i get those sprockets?

Great buddy safe money time and life

Didn't replace zinc spring seats?

Time to get back to lifting body’s off range rovers you’ve been working on MG’s toooooo long 😂😂😂😂

Please give us some of your normal videos 🥲🥲🥲🥲🥲🙈🙈🙈🙈🙈did you take too many pills today 😂😂😂😂😂

I went to a Ham Radio exhibition once just to C the Q

That’s awesome/weird as hell! That’s the whole reason I scan the SW and the ham channels! Nice find, but yes, what the fuck is that?!?

what in the elevator in a outhouse is going on 😂😂😂

That sounds really spooky

Eins zwei polizei 😄

That’s got to be the easiest to change wishbone bush I’ve ever seen😮!

Just tell the people what kind of car is that gracias de Guatemala..

@pistonbroke I have the same issue and will take it into a garage…how much should I expect to be charged? Many thanks!

Only had to replace a hub seal but your vid helped a lot. Thanks for the info. Keep it up.

Good video. Shame the bush isn't brass rather than plastic. It would not have pinched the shaft if it was.

It would be great if you made more videos, I really enjoy the content and your description. Even LR Time uses your videos when repairing Range Rover engines.amazing guy!

Nice simple set up, that looks a clone of a mk2 golf.

I used your method today, and it worked beautifully. Thanks for this video.

I've booked my 2013 MG3 which I've had from new into the MG dealer next week to have the timing chain replaced. It's still running the unmodified chain but I'm getting a rattle on cold start up which disappears straight away. There are no other symptoms with starting or running. I'm just doing some long runs down the M6 at the moment so figured I would get it changed now. I was wondering how long should I expect the job to take as I've not been informed by the dealer? They haven't given me a price either but I know how much the kit is so I know it's not cheap but still cheaper than a replacement engine!

The absolute best video on this. And the EPB system is exactly what I thought it was

سلام از آموزشتون سپاسگزارم ولی با اون آچار کلاغی به پیستون ترمزدستی آسیب میزنید و این کار غلطی بود

thanks for the tip on this fix to took the trim off for another problem and found the wire had become disconnected and thanks to this tip fixed it ps do you know where i can get a hose clip for the rear window washer please

Hi. I have an MG3 2018 and recently noticed on the dash an error code which reads (err1) any idea what this means and how to fix? Thanks

How much did all this cost ?

Hello I want buy new crankshaft for citroen c5 x7 with same engine ... Which seller is good or no. I find on ebay APEX from.enfland and on Allegro Inny (motus) but nobody tell my if its good stuf or made from mud. Thx for answer ... Vladimir from Slovakia

Thanks for your info it helped me out

Bravos star

How not to do calipers and pads,you never leave calipers hanging on brake pipes,where is the copper slip,no torque wrench.